Tech Specs


The G62 is available in either Cellular 2G or LTE-M / NB-IoT.

2G 2G: SARA-G350-02S-01
850/900/1800/1900 MHz
LTE-M / NB-IoT uBlox SARA-R410M Modem operates on all major global LTE-M and NB-IoT bands.
Supported LTE bands: 1*, 2, 3, 4, 5, 8, 12, 13, 18, 19, 20, 26*, 28 (*roaming bands)
SIM Size & Access Internal Micro 3FF SIM



Module uBlox EVA-M8
Constellation Concurrent GPS / GLONASS
Channels 72 Channel High Sensitivity Receiver
Tracking Sensitivity -167dBm industry-leading tracking performance
GNSS Assistance GNSS almanac data for greater sensitivity and position accuracy
Low Noise Amplifier GPS signals are boosted by a unique low-noise amplifier (LNA) allowing operation where other units fail



Input Voltage 8-36V DC (max)
Self-Resetting Fuse Built-in self-resetting fuse makes installation simple and safe. Stringent automotive power “load dump” tests are conducted to ensure operation in the harshest electrical systems.
Operating Current ~25/50mA when moving
~150mA battery charging
Sleep Current <1mA
Back-Up Battery 1100mAh LiPo internal backup battery pack



Dimensions 125 x 80 x 25 mm (4.92 x 3.15 x 0.98″)
Weight 170 g (6.00 oz)
Housing Ultra-Rugged Nylon Glass
IP Rating IP67 rated housing ensures device can withstand fine dust, high-pressure spray, submersion for 30 mins in 1m of water, and extreme temperatures
Installation 7 wire harness
1m Length
Operating Temperature -20°C to +60°C (connected to external power)
At < 0°C and > +40°C the internal backup battery will not be charged as a safety precaution due to the dangers associated with charging batteries at extreme temperatures.
GPS Antenna Internal
Cellular Antenna Internal
RF Antenna Internal
3-Axis Accelerometer 3-Axis Accelerometer to detect movement, acceleration, high G-force events, and more
Diagnostic LED Diagnostic LED signifies operation status
Flash Memory Store weeks of records if device is out of cellular coverage. Storage capacity for over 10 days of continuous 30-second logging.



Digital Inputs 2 x Digital Inputs with configurable pull-up/down
0-48V DC input range
On/Off thresholds:
Pull-up enabled: low at 0.8V, high at 1.0V
Pull-down enabled: low at 2.0V, high at 2.4V
Digital Outputs 1 x Switched Ground Digital Output
Easily wired up to switch external lights, relays, buzzers, etc.
Can be used to immobilize a vehicle
Ignition 1 x dedicated ignition Digital Input 0-48V DC
5V on/off threshold
1-Wire® or iButton® 1-Wire® or “iButton®” can be used to read Driver ID tags. Readers available to suit multiple card formats.



Auto-APN Auto-APN allows the device to analyze the SIM card and select the correct APN details from a list that is pre-loaded in the device’s firmware
Accident & Rollover Detection Configure accident and rollover alerts triggered by extreme changes in velocity and orientation of vehicle or equipment. Second-by-second GPS data is saved on the device’s flash memory, with a capacity of approximately 2 hours of data. In the event of an accident, a subset of the data (60 seconds before / 10 seconds after) is uploaded to the server automatically (if configured) or can be requested manually for a detailed reconstruction of the incident.
Driver ID Options iButton® interface for Driver ID, access control, and logbooking
Driver Safety & Behavior Monitor speeding, harsh acceleration, braking, cornering, idle times and more to improve safety and prevent unnecessary wear on vehicles
Geofence Alerts The server can use device location to create geofences and alerts if an asset enters or leaves designated locations
Geofence Download to Device Geofences can be downloaded directly to the device from Telematics Guru for enhanced location-based actions and alerts.
Maximum of 20 Geofences with up to 30 points per geofence.
GPS Jamming Detection GPS Jamming or Interference can be detected and alerted on
In-Vehicle Alerts Can be wired up to external buzzers or lights for in-vehicle alerts
Lone Worker Safety Interface a variety of duress pendants to enable man-down alerts for lone worker safety monitoring
Preventative Maintenance Set reminders based on distance traveled and run hours to reduce maintenance and repair costs
Real-Time Tracking Device remains continuously connected while on the move for real-time asset tracking
Theft Recovery
Switch to Recovery Mode in the case of theft or loss to activate real-time tracking for asset retrieval
Remote Immobilization Digital outputs can be connected to a relay to enable remote immobilization of vehicles and equipment in the case of theft, abuse, or unauthorized usage
Run Hour Monitoring Calculate run hours and distance traveled (odometer) to understand and optimize asset utilization
Sensor Monitoring Interface with a range of devices and switches for seatbelt detection, duress and panic buttons, lights, in-cab warning buzzers, and more
Tamper Alerts Instant alert if the device is removed from your asset or disconnected from its power source



Flexible Configuration Configure device parameters such as position update rate, movement and accelerometer settings, and more to fit any tracking application
OEM Server Manage, monitor, configure, debug, update, and restart devices remotely from our cloud-based device management system



Third-Party Integration TCP Direct or HTTPS Webhook



Data Security Military-level AES-256 Encryption from device to OEM Server to protect the integrity and confidentiality of telematics data.
Data forwarded to third-party systems is sent via HTTPS for end-to-end security.



Manufacturer’s Warranty One year manufacturer’s warranty



Please contact us for a full list of compliance specifications and documentation for your region. LTE-M / NB-IoT – FCC, ISED, ACMA (DoC), CE (Doc), VERIZON
2G – ICASA, CE (Doc)

How can we help you?